ELEGRP Occupancy Motion Sensor Light Switch, PIR Infrared Motion Activated Wall Switch, No Neutral Wire, Single Pole for CFL/LED/Incandescent Bulb, with Wall Plate, UL Listed (10 Pack, Matte White)

Love this thing! Works great!
MOTION SENSOR LIGHT SWITCHI am NOT an electrician, and this little project scared me, because I don’t like messing with AC current.I did, however, manage to flip the breaker (cut the power) and successfully install this switch. This, despite the fact that my house was built in 1977. Before I ordered this, I took the old plate off of the old switch and looked inside to see if there was a ground. I did see some shiny copper in the back of the tiny old switch box, assumed it was ground (it was), and bought this switch.If any of you have a house like mine, you will realize that every light switch has two black wires attached to it. One wire is the LINE, and one is the LOAD. Without getting into the physics of AC current, this essentially means the SOURCE of the current, and the DESTINATION. Again, not an accurate physical description, but, a logistically apt metaphor.BONUS #1: This switch doesn’t require a ‘neutral’ connection. That is to say, you don’t have to cut into the ‘white’ wires in the box. BIG PLUS for me, as this little switch box seemed to be a fairly major junction for the rest of my house…Anyway, the first step (after cutting the power, of course), was to unscrew the old switch from the box. It became clear what was LINE and what was LOAD. Almost everything was connected to LINE, and there were a couple of wires that headed out to the garage lights that I wanted to control – the LOAD. After that, it did take a little while for me to disconnect the old switch, that was almost as old as I am, from the black leads.Then I had to turn to the ground. It was all kinds of shiny copper in the back of my switch box (behind all of the white wires). I used the same small screwdriver that I used to remove the old plate and switch to pull the wires forward. I then started to connect the new switch, by wrapping the green wire (right handed, as that’s the way the nuts twist on) around the end of the collection of ground wires, and screwing on the wire nut.BONUS #2: The 3 wire nuts that are included are long for their size, helping to protect against any short circuits; and, are pretty sturdy when you are screwing them on.I then proceeded to do the same with the LINE and LOAD wires, wrapping the black and red wires (respectively) first. However, I did find that the exposed wires that came out of my old switch to be too long for comfort, and trimmed them back before screwing on the nuts.With everything connected, I carefully stuffed (if there is such a thing) all of the wires back into the box, and screwed the new switch into place.It acted a little weird, at first. I say this because the switch, lights, and breaker box are all in my garage; so, I could see what happened when I flipped the breaker back on. The lights came back on immediately, then went back off, then came back on. All in under two minutes. I read somewhere that you should allow the switch to ‘boot’, whatever that means.After the ‘boot’ period, though, EVERYTHING HAS WORKED GREAT! I am so tickled. Something so simple has made such a wonderful difference in my life. We have dealt with this garage light problem every since we bought our house almost 22 years ago. Soooo awesome!Even my wife is skeptically excited. Her comments were, ‘It works!’. Shortly thereafter, she asked me to turn on the light in the laundry room for her. I told her that if she liked the garage thing, that I could do the same for the laundry room.BONUS #3: You can still cut your lights on and off manually. This wasn’t clear to me in the descriptions; but, regardless of your settings, you can use the ‘button’ to both turn on AND turn off your lights. However, and this makes sense, after you manually turn OFF your lights, there is a 30 second period before motion will turn the lights back on.

Easy to install and program
Works like a charm, easy to install with no need for C wire and easy to program.Just I noticed a little delay to turn on the light compared to other brands but it general it works perfectly

Last and works perfect
Lasting and quality 100% good

BEFORE YOU BUY: Check light switches for ground wires!!
This is a great product and fairly easy to install. We love the one we installed in our laundry room. You can easily adjust the sensitivity (how close you have to be to set it off) and the time-out. We set ours for 5 minutes , but you could just as easily set it to time out after 30 seconds and be fine, because it will stay on as long as there is motion in the room. The installation tutorial video is super helpful. However, you MUST have a ground wire for the switch to function. I know it seems like a given, but check your switches first! We just assumed that would be universal throughout our house and ordered a pack of 6 without even thinking to check first. We were so pleased with the one we installed in the laundry room, but when we tried to install in a couple of other high traffic areas in the home, we discovered that whoever wired the house before we bought it cut back all the ground wires. They were too short for even a professional electrician to pull them out to connect to the switch. The electrician said he doesn’t know why some people do that, but they do, and these switches HAVE to have a ground wire or they won’t function as a motion sensor. So now we are stuck with the 5 remaining switches that we can’t use. 🙁 Definitely not the fault of the product or the company, just something to consider before ordering!

Easy install, functions as it should.

Just have to know the difference in colour wiring between USA ( this product) and Australia and it should work .

Very useful in our bathrooms